This cold-process shower soap recipe is the best ever. It makes a moisturizing yet cleansing bar with tons of lather. Please read below the recipe for tips on substations, safety, and storage, as well as step-by-step photos. If you’re brand new to soapmaking, there’s a lot to learn! You’ll want to watch the video and read the whole post before you start.
The Best Cold Process Soap Recipe
A super bubbly homemade soap with great cleansing and moisturizing properties. Once you try this recipe, it will be all you want to use!
Prep Time 30 minutes minutes
curing time 1 day day
Total Time 1 day day 30 minutes minutes
Equipment
Safety gear
digital scale
Ingredients
- 11 ounces coconut oil
- 9 ounces olive oil
- 9 ounces palm oil
- 2 ounces sweet almond oil
- 4 ounces castor oil
- 4 ounces avocado oil
- 2 ounces mango butter
- 5.83 ounces lye
- 10-15 ounces water
- 3 tablespoons fragrance oil for a strong scent, vary this to your preferences
- 2 teaspoons sodium lactate optional, for a harder bar
- colorant or mica optional
Instructions
Using a digital scale, measure out the lye and water in separate glass containers. Combine them by adding the lye to the water. (Remember: snow floats on the lake.). Stir until the lye dissolves. The temperature will shoot up. Place this in a safe place to cool.
While the lye solution is cooling, measure out the oils and butters and combine them in a large stainless pot. Melt them over low heat and heat them up to 130-140 degrees. Set them aside to cool.
After 2 hours, check the temperature of both solutions. They should be around 110 degrees. (A range of 100-120 is fine.). If not, allow them to cool longer.
Prepare your mold and measure out any fragrance or color you will be adding. (For best blending of colors, mix some color into a few drops of melted oils.). If using sodium lactate, add it to the lye water at this time.
Pour the water and lye solution into the pot with the melted oils. Blend with a stick blender until thin trace is reached. The soap batter will noticeable thicken and a trail of soap will sit on top of the liquid rather than immediately sinking in. (This will take about 1 minute.). Add the color and fragrance and stir by hand.
Immediately pour the soap batter into the mold. Place in a turned off oven or wrap with blankets to insulate the soap.
After 24 hours of curing, unmold and cut into bars. The bars may seem slightly soft but will harden considerably during the curing process. Allow to cure at least 3 weeks in a well-ventilated place.
Notes
Follow standard soap making safety guidelines!
Table of contents
- ❤️ Why you’ll love this recipe
- 🧂 Ingredients
- 🥣 Equipment
- 🍴Instructions
- 🥫 Storage Instructions
- 🔍 FAQs
- 👩🏻🍳 Expert tips
❤️ Why you’ll love this recipe
- Perfectly balanced between cleansing and moisturizing: Every oil brings its own properties to a bar of soap, and finding the perfect soap recipe is a balance of those things. This recipe does it.
- Tons of lather and big bubbles. This is most people’s complaint about homemade soap, and this recipe takes care of it.
- Suitable for beginners. Yes, it has a lot of oils, but the basic process is the same as any recipe. If you’ve never made cold-process soap before, you should read my Beginners Guide to Soapmaking first.
🧂 Ingredients
This is an overview of the ingredients. You’ll find the full measurements and instructions in the printable recipe at the bottom of the page.
You’ll need the following for this bubbly bar:
- coconut oil
- olive oil
- palm oil
- sweet almond oil
- castor oil
- avocado oil
- mango butter
- lye
- water
- fragrance and color (optional)
- sodium lactate for a harder bar
🥣 Equipment
- Basic stick blender
- Sturdy silicone mold
- Safety equipment (gloves, goggles, apron)
🍴Instructions
Step One: Measure water and lye
First measure your lye and water separately using a digital scale, then carefully combine them. Pour your water into a cup you don’t care much about, then add the lye to the water, stir it until it dissolves, and set it somewhere it will not be knocked over, drank, or otherwise messed with.
Step Two: Measure, melt, and cool the oils
Melt them on your stovetop, bringing the temperature up to around 140.
Now everything needs to cool to about 110 to 120 degrees. It will take a few hours. Check with a thermometer.
If you’re using sodium lactate, add it now to the cooled lye water.
Step three: Blend to trace
Once your temperatures are right, it is time to combine. Pour the lye water into the pot of oils and stick blend.
Important: Before you do this, make sure any color and fragrance you want to add are ready to go, and that your mold is prepared. Things will move very quickly and you don’t want your soap batter hardening in the pot.
Until everything is combined and you have reached a thin “trace”. This means your soap had thickened up JUST a little. If you were to drizzle a bit of soap on top, it would stay instead of sinking in.
Step Four: Add color and fragrance and pour into mold
Add color and fragrance and stir by hand or slowly with the stick blender.
Then pour everything into your prepared mold.
Step Five: Cure and cut
Let the soap cure in a warm, draft-free place (such a turned-off oven that has been warmed to 140 degrees, then turned off), or wrapped in quilts.
The next morning or afternoon you take it out and cut it into bars. Let it cure for 3-5 weeks before using in the shower
🥫 Storage Instructions
Once fully cured, homemade soap should be stored in a dry, well-ventilated spot. I like to put it in shoe boxes in the closet with layers of newspaper in between the bars.
While it is in use, use a soap saver to keep your bar dry. It will last much longer.
🔍 FAQs
What kind of mold did you use?
A 10-inch silicone mold. It’s my favorite for most soaps.
What type of color is this pink?
It is a pink mica from Nurture Soap. You can find it here.
Can I use this recipe in individual cavity molds?
Yes, absolutely. I’d recommend using sodium lactate since it can be a bit soft when unmolding it.
What are the best soap fragrances?
This is 100% personal preference (except for the fact that florals are more difficult to work with). My personal favorites are Comfort and Joy from Nurture Soap and Mango Mango from Brambleberry
Will this recipe work with swirls or embeds?
Yes! I used to swirl it all the time before I got too lazy. 😊
Can I resize this?
You sure can. You’ll need the following percentages:
Coconut Oil: 26.83%
Mango Butter: 4.88%
Olive Oil: 21.95%
Palm Oil: 21.95%
Sweet Almond Oil: 4.88%
Enter them into a soap calculator with the desired size of your batch and it will give you the correct amounts.
👩🏻🍳 Expert tips
- Working with lye is dangerous and you must be in a well-ventilated, distraction-free workspace. Wear goggles and gloves to protect yourself and keeps kids and pets away.
- You must follow soapmaking recipes exactly. If you’re going to make changes or substitutions, you must first run the recipe through a lye calculator and accept that you’ve created your own recipe at this point.
- Castor oil is the “secret” to big bubbles. Don’t substitute!
📘 Related Recipes
- Lemon Soap Recipe
- Homemade Bar Dish Soap
- Oatmeal Soap Recipe
- Homemade Hand Cream for Winter
